Ashworth Conveyor & Transfer Belting Glossary

Conveyor and transfer belting has its own vocabulary — and knowing the difference between a cage and a drum, or a balanced weave and a conventional weave, makes it easier to spec the right belt, troubleshoot a running system, or simply read a quote. This glossary defines the terms Ashworth engineers, sales teams, and customers use every day across woven wire, flat wire, plastic modular, and hybrid belting, plus the spiral systems that run them. Use the index below to jump to a term, or search the page for the word you need.

A  ·  B  ·  C  ·  D  ·  E  ·  F  ·  G  ·  H  ·  I  ·  K  ·  L  ·  M  ·  N  ·  O  ·  P  ·  R  ·  S  ·  T  ·  U  ·  W

A

A5SC Flat Wire Belt

Designed for the can industry by Ashworth. Its special construction allows it to run under inverted cans, without pinching and upsetting them, which can occur at the discharge of the dryer section in a can washer, where the cans transfer onto the take-away conveyor.

Advantage™ Belts

Hybrid belts comprised of acetal links connected by stainless steel rods. Rods are designed to easily snap in/out for quick replacement and maintenance. First NSF certified and USDA accepted plastic belting.

Auxiliary Drive

The sprocket drive that sets the belt speed. This normally is located at the discharge of a spiral conveyor just before the take-up. (See also Take-up)

↑ Back to top

B

Baking Band

The tightly woven wire mesh of Ashworth's Baking Bands provides uniform heat distribution along with excellent air circulation and product support for all but the most fluid of doughs. The density of the band maintains even heating for a consistent bottom bake across the entire width of the belt.

Balanced Weave

A woven mesh consisting of alternating right and left-hand spirals joined by crimped connecting rods to form a continuous belt. In some meshes, straight connecting rods are used.

Bar Capping

Wear strips, typically UHMWPE, installed on the cage bars of a spiral system.

Bar Links

Links typically used on Omni-Flex® belts that determine the strength of the belt. The bar links are assembled in a “shingled” configuration to allow the links to nest as the inside belt edge collapses in a turn.

Belt

A complete product consisting of a skeleton with or without mesh and attachments suitable for flexing around pulleys, sprockets or drive rolls used primarily as a means of conveyance. Also called a "band" (in the baking industry), or a "mat" (in the can making industry).

Belt Supports

Structure on which the belt rides. Typical belt supports are UHMWPE and metal rails which can be arranged in a herringbone pattern or arranged horizontally in the direction of belt travel.

Belt Trackers (Control Rolls)

Devices used to guide the belt’s path. Control rolls are placed 1.5 x belt width from terminals.

Brazed Edge or Soldered Edge

An edge finish completed by brazing or soldering only.

Burrs

Metal protrusions on metal parts due to dull tooling, improperly punched, or cut parts of the belt.

↑ Back to top

C

Cage

Large cylindrical shaped core of a spiral system. The system’s main driving component. (See also Drum)

Cage Bars

The vertical members that form the driving surface of the cage or drum in a lotension spiral system.

Cantilever

Horizontal structural member on which the belt supports are mounted with one end attached to the support columns and the other end free. Typically found on lotension systems.

Catenary

Unsupported section of belt, typically immediately following drive sprockets, which accumulates belt and acts as a weighted take-up.

Center Link Position

Distance between inside edge of belt and centerline of center link in small radius belts.

Chain Driven Belts

A belt construction which provides positive sprocket engagement by incorporating two or more rows of chain attached to cross rods or flatbar. Chains commonly used for this purpose include attachment, engineering, pintle, or roller.

Chordal Action

Variation in speed or surging of the belt caused by the acceleration and deceleration of the belt as it goes around the sprocket. Also known as Pitch Line Rise and Fall.

Christmas Tree

Condition due to high tension. The inside edge of the belt rises up off the belt supports. The belt may get caught between the drum and inside belt supports. (See Reverse Christmas Tree.)

Cleatrac® Belting (CTB)

Precision balanced weave wire mesh consisting of alternating right and left-hand spirals joined by crimped connecting rods, driven by matching sprockets.

Column

The structural member that forms the main belt support for the entire spiral system and is located circumferentially around the system.

Compound Balanced Weave

A mesh consisting of alternating right and left-hand spirals nested together and joined by three or more crimped connecting rods. In some meshes, straight connecting rods are used.

Connector Rod

A wire or rod of any shape (usually round), either straight or crimped, used for joining belt components.

Conventional Weave

A mesh consisting of a series of either all right or all left-hand spirals, each turned into the preceding spiral to form a continuous belt. (For basic types, see Uni-Directional and Sectional Weave.)

Crimped Connectors

Round wire formed into peaks and valleys to connect woven spirals. The design pre-seats and stabilizes spirals to reduce break-in stretch and prevent lateral spiral movement.

Cross Over

Length of straight running belt between centers of two cages on a two cage/one belt system.

↑ Back to top

D

Dancer Roll

Weighted roll at the bottom of a take-up loop.

Dirty Systems

Process dirt and belt wear debris may contaminate product, increase system friction, and accelerate belt wear, thus reducing the useful life of the belt if the user does not practice proper cleaning. Cleaning practices and schedules are application specific.

Dividers

Devices used to separate a belt into longitudinal product lanes. These can be created with woven wire designs or plate attachments.

Double Balanced Weave

A mesh consisting of pairs of interlaced right and left-hand spirals joined by crimped or straight rod connectors so that the pairs of spirals are interspaced by the adjacent spirals.

Double Rod Reinforced Weave (Dual or Duplex Weave)

A mesh consisting of pairs of either all right-hand or all left-hand spirals, each pair being turned into the preceding pair, and reinforced with a rod through the hinging point of the spirals.

Down Cage

A spiral system where the belt travels from top to bottom. (See also Up Cage)

Drum

Large cylindrical shaped core of a spiral system. The system’s main driving component. (See also Cage)

Drum Diameter

Diameter of the drum or cage.

↑ Back to top

E

Edge Drives

Designed to reduce tension to acceptable levels in applications where long belts pass through a series of turns and straight runs, often resulting in tension levels which exceed recommended limits.

End Lock

Rod cap with locking lip inserted into the module along both edges of the belt to secure rod position.

ExactaStack™

Self-stacking belt available in all widths, tier heights, and mesh configurations for both spliced-in sections and complete belt replacements. No system drive modifications required.

Extended Sidebar Chain

A retaining edge provided by special attachments on the chain.

EZ Transfer Finger Plate

Eliminates the need for transfer dead plates at terminal discharges as the tines of the plates fill the space between the raised leg pickets or modules.

↑ Back to top

F

Fatigue Resistant Cleatrac

Provides up to 2.5 times the working strength of our standard Cleatrac belts. Fatigue Resistant Cleatrac belting can be used in applications requiring longer conveyor lengths and increased belt strength.

Filled Edges

Short lengths of wire (any shape) affixed between connectors.

Filler Rod

A rod of any shape (usually round) inserted through a spiral or spirals to fill the mesh. These rods do not connect spirals or belt components.

Flat Bar

A commercially available or manufacturable flat bar used as cross supports to connect chain. Occasionally, flat bar is inserted through mesh to act as a filler bar or assembled under the mesh with the mesh welded to the flat bar.

Flat Wire Belt

Continuous assembly of flat wire pickets connected by a straight round connector inserted through positioned holes.

Flights (Lifts, Cleats)

Devices attached across the width of the belt at prescribed intervals to prevent the product from sliding on the inclines and declines. These may be fabricated from woven wire spirals and formed or unformed sheet metal.

Flip-up

Condition due to high tension. The outside edge of the belt rises up off the belt supports. The belt may get caught between the drum and inside belt support. Also called Reverse Christmas Tree. (See Christmas Tree)

Flip-up Detection

Electrical or mechanical/electrical device(s) that detect a edge flip-up condition.

↑ Back to top

G

Guard Edge Plate

Plates assembled between links and mesh to prevent product from falling off belt. Guard edge plates may be tack welded to links as needed to secure position.

↑ Back to top

H

Herringbone

Arrangement of support rails in a “V-shape”. Tip of “V” points in direction of belt travel. Provides even distribution of wear and helps keep the belt centered in its path.

High Tension

Tension reaching or exceeding the capabilities of the belt. Can result from system layout, high coefficient of friction between belt and product (dirty system), or product loading.

Hold Downs

Members that limit the amount the belt edges can rise in a Christmas Tree or flip-up condition.

↑ Back to top

I

In-Run

The length of belt from the load point to point tangent to the cage of a spiral system or turn of a fixed turn conveyor. Also known as in-feed.

Inside Radius

The distance from the rotational axis (center) of the drum or radius to the inside edge of the belt.

Inside Turn Radius

Turn radius measured to the inside edge of the belt.

Integral Guard Edge

Inside leg link raised to prevent product from falling off belt. Integral guard edge links offer improved cleanup and sanitation over guard edge plates.

Interlocking Looped Edge

A retaining edge formed by extending ends of straight wire connectors or reinforcing wires into interlocking loop design at prescribed angles to the belt.

Interlocking Plate

A retaining edge consisting of a series of formed plates which “interlock” with each other to form a guard edge.

Internal Pigtails

Secures the rod position within the overlay spirals. They are recommended for applications with a soft or wet product. Internal pigtails may be added to any Omni-Tough® overlay at the time of fabrication. Minimum belt width for this feature is 12" (305 mm) nominal.

Interwoven Weave

A mesh consisting of two conventional weaves in which one is woven into the other and sometimes reinforced by straight rods through the hinging points of the spirals.

↑ Back to top

K

Knuckled and Welded Edge

An edge finish which is knuckled with ends of the wire forming the knuckle loop, and tack welded or brazed to the spiral to prevent opening of loops.

Knuckled Edge

An edge finish which is complete without welding. The edge is finished by bending back the ends of the spirals to form a loop, generally permitting each individual spiral to flex as a single link in the belt.

↑ Back to top

L

Ladder Edge

An edge finish formed by extending reinforcing wires or connectors beyond the spiral finish and creating an edge in the appearance of ladder chain.

Ladder Edge, Welded

An edge finish similar to Ladder Edge with loops tack welded or brazed.

Lane Dividers

Detachable or non-detachable plates assembled into the belt’s width to create product lanes. Spiral wire lane dividers also available.

Lehr Mesh

A balanced weave wire mesh consisting of alternating right and left-hand flattened spirals fully seated into specifically formed crimped connector rods—commonly used in glass processing systems.

Limit Switches

Switches installed to sound an alarm or stop the system if the position of the take-up roll goes too high or too low. They can detect high tension and prevent some jams.

Loop

One complete turn within a formed spiral.

Looped Edge

A retaining edge formed by extending pairs of connectors or rod reinforcements, and turning.

↑ Back to top

M

Main Drive

The motor, reducer, and other power transmission devices that turn the cage or drum of a spiral system. Also known as the cage drive.

Mesh

Woven wire surface on which the product rests.

Mesh Designation (Flat Wire)

Flat wire belts are constructed in specific mesh designations or opening sizes, such as 1x1, 1/2x1, 1/2x1/2, with other modifications which may vary according to belt width.

Mesh Designation (Woven)

Woven mesh is designated with a letter (Balanced, Conventional, Unilateral) and three numbers to describe mesh construction.

Mobius

Technique where return path is arranged to make the belt turn itself over each successive pass through the system.

Multi-Strand Weave

A mesh consisting of alternating right and left-hand double spirals (side by side as single units) joined by straight connecting rods.

↑ Back to top

N

Nose Roll

Machined radius plate or roller, plastic or metal, located at the conveyor terminals which the belt wraps around, allowing a close transfer.

↑ Back to top

O

Offset Guard Edge

A retaining edge similar to the Shingle type except having a formed vertical step in each place.

Omni-Flex®

A turn-curve belt based off Ashworth's basic flatwire belt. Flat wire pickets are manufactured with slots, rather than holes, in order to allow the pickets to collapse and expand longitudinally. This allows the belt to negotiate spirals and turns. Each rod is secured via buttonhead welds, and belt strength can be increased by adding single or double bar links to the outside edge of the belt.

Omni-Grid®

Omni-Grid® belts are precision crafted from premium quality stainless steel to exacting standards. The finish is smooth and burr-free for quick and easy cleaning, maximizing production. Available in a variety of configurations to negotiate tight turn radii.

Omni-Pro®

Turn-curve belt with metal links and rods and assembled with a zero tension, 360 buttonless welds, capable of accommodating turns in a conveyor system. Wire mesh overlays are available for greater product support. They can also be used in straight-run applications.

Omni-Tough®

An overlay with a flat surface made from high tensile strength stainless steel wire with a high resilience to impact. Omni-Tough® is available in most mesh configurations.

Opening

Open space on the carrying surface of the mesh between wires.

Opening—Lateral

The nominal inside distance between parallel wires, measured along a line perpendicular to the angle of weave to the nearest intersecting wire whether in the same or adjacent spiral. (This definition does not apply to Compound Balanced Weave.)

Opening—Longitudinal

The nominal inside distance along the angle of weave measured between the connectors of the spirals. (This definition does not apply to Compound Balanced Weave.)

Out-Run

Length of belt from the point tangent to the cage or turn to discharge of the product. Also known as out-feed.

Overdrive

The amount of slippage between the belt and the drum or cage in a spiral system.

↑ Back to top

P

PDCE

Positive Drive Chain Edge. Totally customisable metal belting with good uniformity of pitch, high tensile strength with a relatively light belt/chain weight, and good durability under severe loads.

Picket

A continuous corrugation of flat strip with pre-positioned holes. Applicable to flat wire belts.

Pitch Line Rise and Fall

Also known as Chordal Action.

Plastic Modular Belt

Plastic modules assembled with adjacent modules using a round stainless steel rod inserted through the modules.

Prestoflex®

Plastic belting with a connectorless construction made up of plastic modules, which snap or unsnap together for quick and uncomplicated repairs.

↑ Back to top

R

Radius Weight

Simplified formula for estimating belt tension while in contact with the drum in a spiral system. It is another term used to describe the system tension.

Reduced Radius Omni-Grid®

Smallest turn belt radius available with no center link assembled into the belt.

Reinforcing Rod

A rod of any shape (usually round) inserted through the bends of the spirals for the purpose of strengthening the fabric. It does not join spirals or serve as a connector.

Relieved and Reinforced Turned-up Fabric

A retaining edge similar to a relieved turned-up mesh except that hairpin reinforcements are inserted in the disconnected spirals.

Relieved Turned-up Fabric

A retaining edge similar to a turned-up mesh edge providing flexibility by the omission of connectors or rod reinforcements in the turned-up portion of the mesh at prescribed spacing.

Return Path

The path the belt takes in moving from the discharge back to the in-feed.

Rod Looped Edge

An edge finish similar to the Ladder Edge except that reinforcing wires or connectors are extended and knuckled on themselves.

Rod Reinforced Weave

Mesh constructed in the same manner as Conventional Weave, and reinforced by insertion of a rod through the hinging point of the spirals.

Round Wire Sizes

Round wire sizes generally referred to are the nearest American Steel and Wire or Washburn & Moen gauge number with its decimal equivalent and supplied within the standard wire tolerances of wire manufacturers.

↑ Back to top

S

Sectional Weave

A mesh consisting of alternating sections of right and left conventional weave usually joined by means of straight or crimped wires.

Shingle Style Guard Edge

A retaining edge consisting of overlapping flat plates with one edge of the plate on the outside of the preceding plate and the other edge on the inside.

Side Travel

The continuous movement of a belt in a direction either right or left of the centerline of the conveyor. (See Waver)

Small Radius Omni-Grid® (3/4", 1", and 1.5" )

Belt consists of an assembly of rods and links. A center row of heavy duty non-collapsing links forms two product lanes: for 3/4" pitch belts there are standard links on inside and outside belt edges; for 1" pitch belts there are standard collapsing links on inside edge with 1.75" (44.5 mm) pitch collapsing links on the outside edge. All belts are double welded.

Space Saver Omni-Grid® (1")

Belt consists of an assembly of rods and links. A dual row of heavy duty, non-collapsing links are used on the inside edge and a long pitch-expanding link is used on the outside edge.

Sprockets

Used to drive positive-drive belts. These sprockets are generally cast from carbon, stainless steel, or machined UHMWPE and are finished in sizes suitable for application.

Staggered Style Guard Edges

A retaining edge consisting of alternating overlapped inside and outside flat plates.

Stress Corrosion Cracking

The fracture of a metal in a corrosive environment. Austenitic stainless steel belts are susceptible to this phenomenon under certain conditions.

Strip Sizes

Strip sizes for flat wire and Omni-Flex® are generally supplied in dimensions within the accepted tolerances of flat wire manufacturers. Strip sizes also designate the height and thickness of a flat wire strip.

Stripper Bar

Plain rod mounted between the underside of the sprocket and the belt to help disengage the belt from the sprocket as the belt begins its return run.

Super Small Radius Omni-Grid® (SSROG)

Lotension belt with an inside turn radius equal to 0.8 times the belt width. SSROG has the industry's smallest turn radius for spiral and turn curve applications. Maximizes utilization of available floor space, and can turn either left or right, pivoting about a center link

Surge

A loping or jerky operation of the belt due to too much overdrive, varying coefficients of friction of belt supports, and drive problems.

Swing Wide

The occasional tendency of a belt to swing outward in an area prior to or upon leaving a turn or the drum.

↑ Back to top

T

Tack Weld

This process prevents picket compression or narrowing associated with high belt tension. Typically associated with flat wire belts 60" (1524 mm) or greater.

Take-Up

The area of the system where variations in belt length are accommodated or “taken up”.

Take-Up Drive

A name often given to the system sprocket drive. This drive sets the belt speed and dwell time for the system and is located just before the take-up.

Take-Up Tower

The structure or area where the take-up, take-up drive, limit switches, and dancer roll are located in a spiral.

Tensile Stress

This can result from the fabrication of the material or applied stresses to the material in operation. Most commonly caused from high tension in the system.

Tension Drive

Also known as Take-Up Drive or Auxiliary Drive.

Tension Link

Outermost link in a spiral/turn-curve belt to which all system tension is transferred in a spiral application.

Tension Switches (Limit Switches)

Switches installed to sound an alarm or stop the system if the position of the take-up roll goes too high or too low. Limit switches can detect high tension and prevent some jam-ups.

Tier

A 360° element of the spiral, either ascending or descending one level.

Tier Height

The vertical distance from one belt level on the drum to the next higher or lower level. This is a measurement of distance. Also known as Tier Pitch or Tier Spacing.

Tier Pitch

Also known as Tier Height.

Tier Spacing

Also known as Tier Height.

ToughMat®

PTFE Coated fiberglass or Kevlar® mat for IBO/OBO ovens and dryers.

Tungsten Mesh

Conventional weave wire mesh consisting of only left-hand spirals, wound one into the next so as to form a continuous fabric. Special material allows for use in temperature up to 3632°F (2000°C).

Turn Ratio

The ratio of inside turn radius to the belt width.

Turn-up Guard Edge

A retaining edge formed by extending individual connectors or rod reinforcements, and turning them up at prescribed angles and spacings.

Turned-up Fabric

A retaining edge formed by turning up a portion of the belt at a prescribed angle to the carrying surface.

Turning Radius

The radius around which a belt may be flexed. It is commonly referred to as Inside Turning Radius and is established by the nesting of links or pickets at the inside edge of the turn and by the belt width.

↑ Back to top

U

Uni-Directional Weave

A conventional weave mesh in which all spirals are of the same weave, either right or left. Also known as One-Directional weave.

Up Cage

A spiral system where the belt travels from bottom to top. (See also Down Cage)

↑ Back to top

W

Waver

The inherent deviation from a straight line along the mesh edges. (See also Side Travel)

Wear Edges

An additional feature extended beyond the edge of the belt to act as a buffer.

Welded Edge

An edge finish on a woven belt completed by welding only.

Welded Knuckled Edge

An edge finish that is knuckled, and the knuckles completely filled by welding or brazing.

WG Woven Wire

WG belts are constructed with alternating right- and left-hand spirals joined by a crimped connector. European Standard.

↑ Back to top

X formerly Twitter

Ashworth Brothers Instagram

YouTube